06-09-2010, 10:42
non nii...
vastailen lyhyesti koska on paniuttava pehkuihin...
komposiitti tiivisteen aiheuttama lasku on noin 1bar kokoinen, ongelma jos nokassa on paljon overlappia, tuossa valitsemassani tikussa sitä ei ole eli imuvena on kiinni kun pako aukeaa...tarkoittaa että kone ei vaadi niin kovia puristuksia, toki mahdollista on lohkotason/kansien lasku noin 1mm mutta sinne asti ei olla viel keretty koska kannnet teen ensi valmiiksi.
nokka akseli on tarkoituksella mieto, ja olet oikeassa sen suhteen että edullisin vaihtoehto on mennä jousissa harvempi kierroksisiin, varsinkin jos kone näkee hyvin harvoin yli 4000rpm:ää
väännöstä:
normaali roverin vääntö alue löytyy vanhoista buickin/oldsin viri manuaalista jonka postasin hetki sitten palstalle, tuolla muistaakseni puhuttiin jotain 3200rpm
tä,
http://www.seight.com/images/tech/magreps/1961hrm.pdf
virittämäsi roverin kasi, olitko koskenut kansiin tai imusarjoihin yhtään? vai perustuiko koneen viritys puhtaasi nokkaan (vakio) ja ruiskuun (taas vakio??)
nokka akselin valinnasta:
itse päädyin nokkaan overlapin kautta 112-114 asteinen näyttäisi olevan suosiossa ison veden takana kun sakki rakentaa vääntökoneita, jos saavat tehoja valurauta koneista 1hp/cid ja tasaisen vääntökäyrän ynnättynä kohtuullisella polttoaineen kulutuksella käyttämättä julmia puristussuhteita tuo paketti vääjäämättä jaa kiinnostavaksi kulkineeseen jossa 99,9% käyttökierroksista tulee olemaan 1500-2200 kierroksen välissä.
jostain luin nyrkkisäännön että 10ast nokassa vakioon lisää siirtää tehohuippua 500rpm ylemmäs.
vertailukohta voi toki ontua mutta idea on saman suuntainen:
http://www.cfmperformance.com/articles/H...dillac.pdf
jos olisin rakentamassa vääntö isolohkoa tuo mylly voisi olla mielenkiintoinen vaihtoehto...toisaalta 383 pikulohko chevy on erittäin toimiva paketti...varsinkin ahdettuna...
tuolta jotain juttua nokista:
http://www.chevyhiperformance.com/tech/e...index.html
ja loppuun hupilukemiseksi muun artikkeli chevyn virittelystä:
High Horsepower Tips for a 350 Chevy Motor
By Moss Strohem, eHow Contributor
updated: January 12, 2010
I want to do this! What's This?
While General Motors still makes performance parts, many factory parts have been diminished or depleted. But it's now possible to get any part for the 350 and other SBC engines readily in the aftermarket. Manufacturers even offer "kits" with preconfigured components designed to complement one another. In certain factory production configurations, the Chevy 350ci engine has produced more than 1 horsepower per cubic inch. Many engine builders have attained levels exceeding 2 hp per cubic inch with more modern parts in normally aspirated applications without the use of "power adders" such as nitrous oxide injection or turbo- or supercharging.
400-Horsepower Build
Assuming no modifications are made to the shortblock, cylinder heads with between 160 and 180cc of intake port volume and cylinder head combustion chambers that produce a compression ratio of at least 9.5:1 should be used. A camshaft with approximately .480 inch to .490 inch valve lift and 224 and 230 degrees duration on the intake and exhaust lobes, respectively; an aftermarket dual plane intake manifold and carburetor; and a free-flowing exhaust system will reach this power goal. A combination such as this will make good power from 2,500 to 6,000 RPMs. (For heads, the factory GM Vortec 170cc heads are plentiful and can support this power goal with ease, but other aftermarket castings are also available.)
550-Horsepower Build
An engine combination similar to above can be used with a nitrous oxide injection kit with proper ignition timing to approach these power levels, but the crank, rods and pistons will not survive for long.
A 350ci engine with this power goal is going to require stronger aftermarket lower-end components to withstand the loads produced. It will make its power at a higher engine RPM. Great attention to detail in clearances and exact component combination are essential. Since the lower-end components need to be upgraded, this is an opportunity to increase the stroke of the crankshaft and gain additional cubic inches and torque. A common choice is 3.75 inches, resulting in a displacement of 383ci in a standard 4-inch bore. An aftermarket forged-steel crank should be used (no more expensive than a standard-stroke crank); forged rods with high-strength rod bolts are mandatory; and forged pistons will also be required.
To achieve 550 bhp without nitrous oxide injection, the cam/heads and induction will have to be bigger still, and compression of at least 10.5:1 should be targeted (this is the limit for premium-pump fuel). Cylinder heads with 200cc or larger intake ports that flow an efficient, high-quality 290 cfm-plus of air will be needed, as will a roller camshaft with valve lift approaching .580 inch with duration of approximately 252 degrees and a carefully chosen dual-plane or single-plane intake manifold and carburetor.
This engine will be marginally street drivable, and the typical enthusiast may or may not be able to design and build it. A nitrous oxide injection kit can be used with less regard for engine damage, but the ignition timing still needs to be properly managed. For high-horsepower builds beyond these levels, a reputable competition engine builder/machine shop is likely to produce the best results.
Read more: Best Way - High Horsepower Tips for a 350 Chevy Motor | eHow.com http://www.ehow.com/way_5859043_high-tip...z0ymefwIHM
juuh, pakko painua koisiin...
niin lopuksi totean että autossa 5-vaihteinen aski pitkällä 5 vaihteella 0,77...ja ascroftin 1:41 jakorattailla jotka nostavat kierroksia noin 16%...eli jos matikka ei onnu niin 1800-1900 kierrosta 90Km/h vauhdissa...eli juuri siellä missä sitä "vetovoimaa" kaivataan....
niin autosta ei rakenneta rakettia...vaan työjuhtaa, joka voi edelleen toimia puskassa...
vastailen lyhyesti koska on paniuttava pehkuihin...
komposiitti tiivisteen aiheuttama lasku on noin 1bar kokoinen, ongelma jos nokassa on paljon overlappia, tuossa valitsemassani tikussa sitä ei ole eli imuvena on kiinni kun pako aukeaa...tarkoittaa että kone ei vaadi niin kovia puristuksia, toki mahdollista on lohkotason/kansien lasku noin 1mm mutta sinne asti ei olla viel keretty koska kannnet teen ensi valmiiksi.
nokka akseli on tarkoituksella mieto, ja olet oikeassa sen suhteen että edullisin vaihtoehto on mennä jousissa harvempi kierroksisiin, varsinkin jos kone näkee hyvin harvoin yli 4000rpm:ää
väännöstä:
normaali roverin vääntö alue löytyy vanhoista buickin/oldsin viri manuaalista jonka postasin hetki sitten palstalle, tuolla muistaakseni puhuttiin jotain 3200rpm
tä, http://www.seight.com/images/tech/magreps/1961hrm.pdf
virittämäsi roverin kasi, olitko koskenut kansiin tai imusarjoihin yhtään? vai perustuiko koneen viritys puhtaasi nokkaan (vakio) ja ruiskuun (taas vakio??)
nokka akselin valinnasta:
itse päädyin nokkaan overlapin kautta 112-114 asteinen näyttäisi olevan suosiossa ison veden takana kun sakki rakentaa vääntökoneita, jos saavat tehoja valurauta koneista 1hp/cid ja tasaisen vääntökäyrän ynnättynä kohtuullisella polttoaineen kulutuksella käyttämättä julmia puristussuhteita tuo paketti vääjäämättä jaa kiinnostavaksi kulkineeseen jossa 99,9% käyttökierroksista tulee olemaan 1500-2200 kierroksen välissä.
jostain luin nyrkkisäännön että 10ast nokassa vakioon lisää siirtää tehohuippua 500rpm ylemmäs.
vertailukohta voi toki ontua mutta idea on saman suuntainen:
http://www.cfmperformance.com/articles/H...dillac.pdf
jos olisin rakentamassa vääntö isolohkoa tuo mylly voisi olla mielenkiintoinen vaihtoehto...toisaalta 383 pikulohko chevy on erittäin toimiva paketti...varsinkin ahdettuna...
tuolta jotain juttua nokista:
http://www.chevyhiperformance.com/tech/e...index.html
ja loppuun hupilukemiseksi muun artikkeli chevyn virittelystä:
High Horsepower Tips for a 350 Chevy Motor
By Moss Strohem, eHow Contributor
updated: January 12, 2010
I want to do this! What's This?
While General Motors still makes performance parts, many factory parts have been diminished or depleted. But it's now possible to get any part for the 350 and other SBC engines readily in the aftermarket. Manufacturers even offer "kits" with preconfigured components designed to complement one another. In certain factory production configurations, the Chevy 350ci engine has produced more than 1 horsepower per cubic inch. Many engine builders have attained levels exceeding 2 hp per cubic inch with more modern parts in normally aspirated applications without the use of "power adders" such as nitrous oxide injection or turbo- or supercharging.
400-Horsepower Build
Assuming no modifications are made to the shortblock, cylinder heads with between 160 and 180cc of intake port volume and cylinder head combustion chambers that produce a compression ratio of at least 9.5:1 should be used. A camshaft with approximately .480 inch to .490 inch valve lift and 224 and 230 degrees duration on the intake and exhaust lobes, respectively; an aftermarket dual plane intake manifold and carburetor; and a free-flowing exhaust system will reach this power goal. A combination such as this will make good power from 2,500 to 6,000 RPMs. (For heads, the factory GM Vortec 170cc heads are plentiful and can support this power goal with ease, but other aftermarket castings are also available.)
550-Horsepower Build
An engine combination similar to above can be used with a nitrous oxide injection kit with proper ignition timing to approach these power levels, but the crank, rods and pistons will not survive for long.
A 350ci engine with this power goal is going to require stronger aftermarket lower-end components to withstand the loads produced. It will make its power at a higher engine RPM. Great attention to detail in clearances and exact component combination are essential. Since the lower-end components need to be upgraded, this is an opportunity to increase the stroke of the crankshaft and gain additional cubic inches and torque. A common choice is 3.75 inches, resulting in a displacement of 383ci in a standard 4-inch bore. An aftermarket forged-steel crank should be used (no more expensive than a standard-stroke crank); forged rods with high-strength rod bolts are mandatory; and forged pistons will also be required.
To achieve 550 bhp without nitrous oxide injection, the cam/heads and induction will have to be bigger still, and compression of at least 10.5:1 should be targeted (this is the limit for premium-pump fuel). Cylinder heads with 200cc or larger intake ports that flow an efficient, high-quality 290 cfm-plus of air will be needed, as will a roller camshaft with valve lift approaching .580 inch with duration of approximately 252 degrees and a carefully chosen dual-plane or single-plane intake manifold and carburetor.
This engine will be marginally street drivable, and the typical enthusiast may or may not be able to design and build it. A nitrous oxide injection kit can be used with less regard for engine damage, but the ignition timing still needs to be properly managed. For high-horsepower builds beyond these levels, a reputable competition engine builder/machine shop is likely to produce the best results.
Read more: Best Way - High Horsepower Tips for a 350 Chevy Motor | eHow.com http://www.ehow.com/way_5859043_high-tip...z0ymefwIHM
juuh, pakko painua koisiin...
niin lopuksi totean että autossa 5-vaihteinen aski pitkällä 5 vaihteella 0,77...ja ascroftin 1:41 jakorattailla jotka nostavat kierroksia noin 16%...eli jos matikka ei onnu niin 1800-1900 kierrosta 90Km/h vauhdissa...eli juuri siellä missä sitä "vetovoimaa" kaivataan....
niin autosta ei rakenneta rakettia...vaan työjuhtaa, joka voi edelleen toimia puskassa...

WWW
Haku
Jäsenet
Kalenteri
Apuja
Portaali
